1:8 SCALE GAS POWERED OFF-ROAD BUGGYPLEASE READ INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING THIS MODEL.KEEP THIS MANUAL FOR PARTS NUMBERS WHEN ORDERING.I
ASSEMBLY OF THE GEAR BOX( Assemble two gear boxes, front and rear. ) 900265 x 5mm Set Screw306306 x 13 x 5mmBall Bearing306306 x 13 x 5mmBall Bearin
36620Front Shock Tower* Insert front anti-roll bar before assembling shock tower.4 x 16mmFlat HeadTapping Screw30160Front Upper Arm HolderASSEMBLY
Assembly of the right and left hand side are the same.Assembly of the right and left hand side are the same.36901Ball TypeKnuckle Arm( Right and Left
30151Upper arm Shaft900213mmE-Ring900213mmE-RingRR0136905Caster Angle Adjuster* o change the caster angle .use adjuster tCaster angle will become
Assembly of the right and left hand side are the same.368704 X 10mmSet Screw* A 4 x 10mm set screw is used to adjust the ride height.900213mmE-Ring9
ASSEMBLY OF THE REAR HUB360538 x 16 x 5Ball Bearings360538 x 16 x 5Ball BearingsRearHub36082Rear Wheel Axle Shaft360552.5 x 17mmPin36054Wheel Hub( Alu
3 x 15mm Screw0 10 20 30 40 50mm15mm304023 X 30mmTie Rod304016mmBall Joint303406mmStabil
ASSEMBLY OF THE WING SUPPORT3 x25mmTapping Screw3 x25mmTapping Screw3 x 20mmTapping screw3 x 20mmTapping screw30271Wing Support30270Wing Support30271W
ASSEMBLY OF THE SERVO SAVER3 x 15mmScrew36742Servo SaverBushing36742Servo SaverBushing36750Servo SaverConnector3mmNylon Lock Nut3mmNylon Lock Nut36743
0 10 20 30 40 50mm3 x 20mmFlat Head Screw3 x 20mm Flat Head Screw 3 x 15m
REQUIRED FOR OPERATION THINGS NEEDEDAA Batteries ( 12 pcs )Glow Fuel20%TOOLS NOT INCLUDED IN KIT,BUT NEEDED TO MAINTAIN YOUR CAR. Phillips Type Screw
RR34041Chassis5 Degree KickupHard CoatedASSEMBLY OF THE GEAR BOX ONTOCHASSIS3 x 10 mm Flat Head Screw4 x 16mmFlat HeadTapping Screw * Insert the front
3 x 10mmFlat Head Screw( 3 Pcs)34080Nylon Stone Guard(Left-Side)34080Nylon Stone Guard(Left-Side)ASSEMBLY OF THE STONE GUARDAssembly of the right and
3 X 8mm Washer 3mm Nylon Locknut 3 x 5mm Screw 3 x 20mm Cap Screw* Place the clutch shoes with the clutch springs over the 3
INSTALLATION OF THE FUEL TANKAND ENGINE ONTO CHASSIS30280Fuel Tank125cc30287Tank Mount Posts10114Flat Head EngineMount Screws
ASSEMBLY OF THE FUEL TUBE3 x 10mm Tapping Screw3 x 10mm Tapping Screw3 x 10mm Tapping Screw34032Receiver Box34061Radio TrayASSEMBLY OF THE RADIO TRAY
Switch10280Switch Cover* Use the screw provided with your witch. * Connect the wire to receiver. * Connect battery case wire to switch.* Co
* Use the screw provided with your radio.301722mm Rod* Use the screw provided with your radio.10768Steering Servo HornASSEMBLY OF THE SERVO HORN L
A-416mm Ball & Socket304106mmStabilizer Ball End304106mmStabilizer Ball End304023 X 30mmTie Rod304116mm Ball & Socket304116mm Ball & Sock
ALIGN THROTTLE SERVO AND BRAKE SAME AS SHOWNBrake is not onEngine at idle( Neutral Position )Brake is onBrake Adjust Nut ( Braking Position )Brake is
25mm25mm0510152025510 15 20 252626ASSEMBLY OF THE WING* Drill two 7mm holes for mounting. 40084 Wing, Yellow* Check the hole spacing on the unders
MUST READ THIS BEFORE RUNNINGRunning a nitro kit is fun and easy, but to make this a safe rusting.• Clean oil and dirt from chassis with a degreaser.
Assembly of the right and left hand side are the same.RR15072Wheel NutsBlueASSEMBLY OF THE TIRES AND WHEELSINSTANT GLUE* Apply instant glue into t
ENGINE BREAK-IN AND TUNNING(BREAK-IN THE ENGINE BEFORE DRIVING THE CAR!)OPTIONAL OFNA CAR STANDSTUNING AFTER BREAK-INIdle adjuster screw &Barrel S
APPENDIX PAGES
ABCCHECKING ENGINE THROTTLE* Insert into transmitter.1. Insert AA batteries into transmitter (8 Pcs).2.Turn on transmitter.3.Turn on receiver.4.Ce
Insert 8 pcs AA batteries into transmitter. INSTALLATION OF THE TIRES AND WHEELSFront Knuckle ArmAssemblyRear Hub AssemblyNotice direction of the tir
2. Pull down piston, attach pressure top and shock oil overflow with tissue paper. SHOCK ASSEMBLYFILLING THE SHOCKS WITH OILASSEMBLY OF THE SPR
301213 x 5mm Screw(Small Head)30751 Diff. Case ( Front/Rear )30761 Diff. Case (Center ) 30751 Diff. Case ( Front/Rear )30761 Diff. Case (Center ) 30
Screw CementScrew CementASSEMBLY OF THE SPUR GEARASSEMBLY OF THE CENTER BRAKE CAP JOINTASSEMBLY OF THE BRAKE CAM FOR FRONT ASSEMBLY OF THE BRAKE CAM F
31020Brake Disc.31020Brake Disc.ASSEMBLY OF THE CENTER DIFF. MOUNT 30201Center Diff. Mount30201Center Diff. Mount3x15mmScrews3x15mmScrews30180Brake Pa
Commentaires sur ces manuels